Connect with us

    Repair Manual

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    Did you recently put a load of clothes in your Whirlpool washer and have them come out wet?

    If your washer is spinning, but not expelling the water from your clothes there is a problem with your machine.

    While this can be very frustrating, we have some potential problems and fixes for you to try. Here’s a look at what may be happening.

    Here is a shortlist of what may go wrong and what you need to check:

    • Unbalanced Load
    • Drain Hose Clogged
    • Shift Actuator Failed
    • Drain Filter Clogged
    • Defective Drain Pump
    • Lid Switch Failed
    • and more

    This is the simplest of all the fixes we will discuss.

    Sometimes when you wash bulky items such as blankets, it can cause the tub or drum to become out of balance.

    When this occurs the water will not drain properly, and can leave your clothes soaking wet.

    Advertisement

    The washer will not proceed to the spin cycle, once an unbalanced load detected.

    Always try to create a good balance with your wash loads.

    You can do this by adding less or more items to ensure the garments are not too heavy on one side.

    After the wash cycle has ended you will know if this is the issue because the contents in the washer will be primarily on one side. If this occurs, balance it out and run the spin cycle again.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    The next thing you will want to check is the drain hose connected to the back of your washing machine.

    If this hose is bent or clogged it will restrict the water from draining out, and your clothes will come out wet after the cycle is finished.

    You’ll need to disconnect the hose from the drain pump and make sure the hose isn’t bent. Also, check for blockages restricting water flow in both the hose and the drain pump.

    Advertisement

    It’s also a great idea to check that the drain hose is positioned correctly. If the hose is too far or not far enough down inside the standpipe, it can cause improper draining. This in turn causes the Whirlpool washer to not drain the water completely.

    Another common issue with Whirlpool top loading machine is when shift actuator stopped working properly.

    This actuator switch transmission gears between the agitating and spin cycle.

    But also counting revolutions of the basket, cause it have a basket speed sensor.

    If it failed mechanically or electrically, the washer will be stuck in the agitating cycle and will not proceed to the spin cycle.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    Your Whirlpool machine has what’s called a coin trap or drain filter. When this becomes blocked your washing machine will not spin your clothes dry.

    This part is located near the pump and works as a filter to trap any foreign object that gets into the drain. The most common objects are small ones left in pockets such as keys, coins, paperclips, pins, and even small socks, etc.

    Advertisement

    You can find the drain filter behind the access panel on the bottom front of your machine. The filter is easy to clean and once it’s clean the water should flow better when draining from the machine.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    If the hose and filter are both okay, you’ll need to check the drain pump.

    It may be clogged with debris or could be defective and needs to be replaced.

    To check this you will need to disconnect the drain hose, and remove the back panel from your Whirlpool washer.

    Any debris that’s present will be easy to see.

    If there are no visible blockages you’ll want to use a multimeter to test that the drain pump itself is functioning properly.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    Multimeter
    $50 – 599
    Advertisement
    We earn a commission if you click this link and make a purchase at no additional cost to you.

    To check this remove the wire connectors from both terminals on the pump.

    You’ll need to test both terminals. Depending on your individual machine, the multimeter should read somewhere between 5 and 10 ohms.

    If the reading is showing zero, the drain pump should be removed and replaced.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    Your Whirlpool washer may have a belt that helps the drum spin.

    With normal use over time, the belt can become stretched or worn.

    When this occurs it affects how fast the machine can spin.

    Advertisement

    When the washer belt becomes stretched it begins to slide around during wash cycles, and the washer will not be able to reach fast enough speeds to remove all the surplus water from your clothes.

    The belt may be located on the front or back of your washer, depending on your specific Whirlpool model.

    Once you locate it, inspect it for visible wear and tear.

    If the belt is okay it will be snug and won’t wobble when turning the washer drum.

    If the belt is visibly worn, stretched, or it moves when you turn the drum, you’ll need to have it replaced.

    Whirlpool washer will not spin if door lock (for front loading machine) or lid switch (for top loading machine) if malfunctioned.

    Advertisement

    Door lock switch stays in series with wash motor electrical circuit.

    And if the door lock is open, power will not flow to the motor.

    If your Whirlpool is a direct drive washer it may have a failing clutch. The clutch will prematurely wear due to loading the washer improperly.

    You can do an easy eyeball test where you simply lean it back and look at the area surrounding the gearcase and clutch for signs of oil. If there is a lot of oil present, replace the gearcase.

    Or, if you’d like to get more advanced with the eyeball test try this:

    • Use pliers to compress the clutch ring’s spring. Remove it from the drum
    • Check the rivet holes where the ring pads are held in place.
    • If there’s a great deal of debris in the holes, change the clutch.
    • Check the clutch for a glazed look that appears glossy and reflects light. This also signifies that it needs to be changed.
    • When checking these items, don’t remove the outer tub, simply remove the gearcase.

    Finally, if you’ve exhausted every other tip on this list it’s time to check the washer timer.

    Your Whirlpool’s transmission has what’s called a neutral stop. This means the washer is stopped by a timer momentarily during the spin cycle so the spin can be engaged.

    Advertisement

    If your machine doesn’t do this, the washer timer is faulty and needs to be replaced.

    You can check this by monitoring the machine while the load is draining. Once it’s been draining for 3 minutes go ahead and open the lid and close it again. If it spins, replace the timer.

    Have you had similar problems with your Whirlpool washer? What did you do to fix it? Do you have other questions regarding the issue? Leave us a comment below and let’s discuss.

    Did you recently put a load of clothes in your Whirlpool washer and have them come out wet?

    If your washer is spinning, but not expelling the water from your clothes there is a problem with your machine.

    While this can be very frustrating, we have some potential problems and fixes for you to try. Here’s a look at what may be happening.

    Advertisement

    Here is a shortlist of what may go wrong and what you need to check:

    • Unbalanced Load
    • Drain Hose Clogged
    • Shift Actuator Failed
    • Drain Filter Clogged
    • Defective Drain Pump
    • Lid Switch Failed
    • and more

    This is the simplest of all the fixes we will discuss.

    Sometimes when you wash bulky items such as blankets, it can cause the tub or drum to become out of balance.

    When this occurs the water will not drain properly, and can leave your clothes soaking wet.

    The washer will not proceed to the spin cycle, once an unbalanced load detected.

    Always try to create a good balance with your wash loads.

    You can do this by adding less or more items to ensure the garments are not too heavy on one side.

    Advertisement

    After the wash cycle has ended you will know if this is the issue because the contents in the washer will be primarily on one side. If this occurs, balance it out and run the spin cycle again.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    The next thing you will want to check is the drain hose connected to the back of your washing machine.

    If this hose is bent or clogged it will restrict the water from draining out, and your clothes will come out wet after the cycle is finished.

    You’ll need to disconnect the hose from the drain pump and make sure the hose isn’t bent. Also, check for blockages restricting water flow in both the hose and the drain pump.

    It’s also a great idea to check that the drain hose is positioned correctly. If the hose is too far or not far enough down inside the standpipe, it can cause improper draining. This in turn causes the Whirlpool washer to not drain the water completely.

    Another common issue with Whirlpool top loading machine is when shift actuator stopped working properly.

    This actuator switch transmission gears between the agitating and spin cycle.

    Advertisement

    But also counting revolutions of the basket, cause it have a basket speed sensor.

    If it failed mechanically or electrically, the washer will be stuck in the agitating cycle and will not proceed to the spin cycle.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    Your Whirlpool machine has what’s called a coin trap or drain filter. When this becomes blocked your washing machine will not spin your clothes dry.

    This part is located near the pump and works as a filter to trap any foreign object that gets into the drain. The most common objects are small ones left in pockets such as keys, coins, paperclips, pins, and even small socks, etc.

    You can find the drain filter behind the access panel on the bottom front of your machine. The filter is easy to clean and once it’s clean the water should flow better when draining from the machine.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    If the hose and filter are both okay, you’ll need to check the drain pump.

    It may be clogged with debris or could be defective and needs to be replaced.

    To check this you will need to disconnect the drain hose, and remove the back panel from your Whirlpool washer.

    Advertisement

    Any debris that’s present will be easy to see.

    If there are no visible blockages you’ll want to use a multimeter to test that the drain pump itself is functioning properly.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    Multimeter
    $50 – 599
    We earn a commission if you click this link and make a purchase at no additional cost to you.

    To check this remove the wire connectors from both terminals on the pump.

    You’ll need to test both terminals. Depending on your individual machine, the multimeter should read somewhere between 5 and 10 ohms.

    Advertisement

    If the reading is showing zero, the drain pump should be removed and replaced.

    Whirlpool Washer Not Spinning And Clothes Are Still Wet?

    Your Whirlpool washer may have a belt that helps the drum spin.

    With normal use over time, the belt can become stretched or worn.

    When this occurs it affects how fast the machine can spin.

    When the washer belt becomes stretched it begins to slide around during wash cycles, and the washer will not be able to reach fast enough speeds to remove all the surplus water from your clothes.

    The belt may be located on the front or back of your washer, depending on your specific Whirlpool model.

    Once you locate it, inspect it for visible wear and tear.

    Advertisement

    If the belt is okay it will be snug and won’t wobble when turning the washer drum.

    If the belt is visibly worn, stretched, or it moves when you turn the drum, you’ll need to have it replaced.

    Whirlpool washer will not spin if door lock (for front loading machine) or lid switch (for top loading machine) if malfunctioned.

    Door lock switch stays in series with wash motor electrical circuit.

    And if the door lock is open, power will not flow to the motor.

    If your Whirlpool is a direct drive washer it may have a failing clutch. The clutch will prematurely wear due to loading the washer improperly.

    Advertisement

    You can do an easy eyeball test where you simply lean it back and look at the area surrounding the gearcase and clutch for signs of oil. If there is a lot of oil present, replace the gearcase.

    Or, if you’d like to get more advanced with the eyeball test try this:

    • Use pliers to compress the clutch ring’s spring. Remove it from the drum
    • Check the rivet holes where the ring pads are held in place.
    • If there’s a great deal of debris in the holes, change the clutch.
    • Check the clutch for a glazed look that appears glossy and reflects light. This also signifies that it needs to be changed.
    • When checking these items, don’t remove the outer tub, simply remove the gearcase.

    Finally, if you’ve exhausted every other tip on this list it’s time to check the washer timer.

    Your Whirlpool’s transmission has what’s called a neutral stop. This means the washer is stopped by a timer momentarily during the spin cycle so the spin can be engaged.

    If your machine doesn’t do this, the washer timer is faulty and needs to be replaced.

    You can check this by monitoring the machine while the load is draining. Once it’s been draining for 3 minutes go ahead and open the lid and close it again. If it spins, replace the timer.

    Have you had similar problems with your Whirlpool washer? What did you do to fix it? Do you have other questions regarding the issue? Leave us a comment below and let’s discuss.

    Advertisement

    Trending